Stepper Motor Drive Simple Controller Pwm Generation Controller Pulse Generation

Brand: Unbranded

Sоlgt af:

Stepper Motor Drive Simple Controller Pwm Generation Controller Pulse Generation

Brand: Unbranded

179,00 DKK

Spar 180,00 DKK (50%)

Vejl. Pris

~~359,00 DKK~~

På lager

+ 42,49 DKK Levering

Sоlgt af:

179,00 DKK

Spar 180,00 DKK (50%)

Vejl. Pris

~~359,00 DKK~~

På lager

+ 42,49 DKK Levering

Vi accepterer følgende betalingsmetoder

Beskrivelse

1.When the controller generates a pulse frequency signal,it can be supplied to the stepper driver as a signal.If you want to control the stepper motor,it must also be equipped with a driver.This simple controller + stepper driver + stepper motor + DC power supply can form a simple control platform.2.The controller can generate pulse frequency signal and PWM pulse width signal.There is a jumper on the board,which can be set and selected.By default,it is set to generate pulse frequency signals.REQ is to generate a pulse frequency signal.PWM is to generate PWM signal3.When the controller generates a pulse frequency signal,there are three frequency signals of high,medium and low,which can be selected by the jumper.The frequency parameters are about: High: 5.8KHZ-127KHZ; Middle: 590HZ-15.8KHZ; Low: 82HZ-2.3KHZ,Frequency measurement: PUL and common cathode (GND) ports can be measured.4.There are 2 groups of power input for power supply,and 2 groups only need to be connected to one group of power supplies.It is recommended to use a power supply above 15V.Connect to the power supply of the 2-position terminal,and do not reverse the positive and negative.One group is the power supply connected to DC 15-160VDC,and the recommended working voltage is 15-80VDC.The other group is 5-12VDC.When used with the driver,it is recommended to use a minimum of 12V,do not use a 5V power supply for power supply,it is not too much at 5V,the power supply is connected to 5-12V input,and the negative power supply is connected to common cathode.2.Wiring instructions1.For the wiring of each wiring port,there are silkscreen instructions next to the terminals.Common cathode or common anode can be connected to the stepper motor driver.PUL: Pulse portDIR: Direction port: enable portCommoncathode: common ground (GND)Common anode terminal: common terminal (+5V)5-12V power supply is positive: the positive terminal of 12V power supply is generally empty,it is recommended to use a power supply above 15V.Material: PCBcolour: As shownPackage Contents:1 x Stepper Motor ControllerOnly the above package content,other products are not included.Note: Light and different displays may cause the color of the item in the picture a little different from the real thing.The measurement allowed error is +/- 1-3cm.

Brand: Unbranded
Kategori: Laderegulatorer

Fruugo ID: 373926406-810044396

Produktsikkerhedsinformation

Se venligst produktsikkerhedsoplysningerne, der er specifikke for dette produkt, beskrevet nedenfor

Følgende oplysninger leveres af den uafhængige tredjepartsforhandler, der sælger dette produkt.

Produktsikkerhedsmærker

Sikkerhedsadvarsler: Not suitable for children under 24 months old,choking hazard,adult supervision required

Levering og returnering

Sendes inden for 24 timer

STANDARD: 42,49 DKK - Levering mellem kl fre. 05 december 2025–tor. 11 december 2025

Afsendes fra Kina.

Vi gør vores bedste for at sikre, at de produkter, du bestiller, leveres til dig fuldt ud og i henhold til dine specifikationer. Skulle du dog modtage en ufuldstændig ordre eller andre ting end dem, du bestilte, eller der er en anden grund til, at du ikke er tilfreds med ordren, kan du returnere ordren eller produkter inkluderet i ordren og modtage en fuld refusion for varerne. Se fuld returpolitik

Detaljer om produktoverholdelse

Se venligst overensstemmelsesoplysningerne, der er specifikke for dette produkt, beskrevet nedenfor.

Følgende oplysninger leveres af den uafhængige tredjepartsforhandler, der sælger dette produkt.

Producent:
De følgende oplysninger angiver kontaktoplysningerne for producenten af det relevante produkt, der sælges på Fruugo.

QuanZhouCeYue ShangMaoYouXian GongSi
QuanZhouCeYue ShangMaoYouXian GongSi
520, Building 5, Cross-border E-commerce Park, Donghai Street, Fengze District, Quanzhou, Fujian
Quanzhou
CN
362000
ceyuehe@163.com
15060867585

Ansvarlig person i EU:
De følgende oplysninger angiver kontaktoplysningerne for den ansvarlige person i EU. Den ansvarlige person er den udpegede økonomiske aktør med hovedsæde i EU, der er ansvarlig for overensstemmelsesobligationerne i forbindelse med det relevante produkt, der sælges til den Europæiske Union.

Axitera GmbH
Axitera GmbH
Kreuznacher Str. 30, D-60486 Frankfurt am Main, Hessen, Germany
Frankfurt am Main
DE
60486
infonoticeeran@gmail.com
(+49) 6934873848