Beskrivelse
1、When you fit the wire screw set in the screw hole of the workpiece of aluminum alloy and other materials, the product can form a high‑strength, wear‑resistant, high‑accuracy standard female thread
2、You can repaire the threaded hole in a cost‑effective manner. When a thread error occurs or a damaged female threaded hole is repaired, threaded insert can be used as a repair method
3、Thread inserts can be used to convert between metric and inch thread holes, very convenient and fast
4、Using high‑strength, high‑accuracy diamond‑shaped cross‑section steel wire. Wire thread inserts are also called threaded sheaths, stainless steel threaded sleeves, wire sleeves, which is a new type of female threaded fasteners
5、Applied to low‑strength engineering materials such as aluminum alloy, zinc alloy, alloy, copper, plastic, engineering plastics, etc. can significantly improve thread strength and wear resistance
100 x Thread Inserts
Item Type: Thread InsertsMaterial: SUS304Model: M4x
0.7Thread Specification: M4x
0.7 (mm)Outside Diameter Before Installation: Approx. 5 ~
5.3mm /
0.2 ~
0.2inDiameter of Drilling Drill Bit for Installation: Approx.
4.2mm /
0.2in1D/
1.5D/2D/
2.5D/3D:Length After Installation: Approx. 4mm /
0.2in6mm /
0.2in8mm /
0.3in10mm /
0.4in12mm /
0.5inNumber of Turns Before Installation: 4/
6.6/
9.1/
11.7/
14.2Thread Protective Sleeve Model Specification Description: For Example: M3x
0.5X
1.5D, which means that after the screw set is completed, the female thread is M3, the pitch is
0.5, and the length is
1.5D (length refers to
1.5 times the diameter, that is,
1.5x3=
4.5mm ), the length here refers to the length after installation.How to Use:
1. DrillingUse the drill bit of the size listed in the parameter table of the wire thread insert to drill the hole. Be careful not to drill the hole into a cone shape. The chips generated by the drill hole must be blown out with compressed air. After drilling, the counterbore should not exceed the depth of
0.4 pitch. Too large counterbore is not conducive to the screwing of the wire thread insert.
2. TappingUse special taps for wire thread inserts to tap. The depth of the tapping must exceed the installation length of the thread inserts. After tapping, use a compressed air spray gun to blow out the debris. When the thread accuracy is high, check the tapped bottom hole with a special bottom hole plug gauge for wire thread inserts.
3. InstallationPut the wire screw sleeve into the installation wrench (figure 5 on the right), insert the wire screw sleeve installation tail handle into the guide rod groove of the installation wrench, and turn the handle of the installation wrench to screw the wire screw sleeve into the screw hole. For installation of M14x2 or more phase thread thread inserts, you can use the "T" type slotting simple tool to install; Note: During the installation and screwing process of the thread inserts, there should be no pressing in the vertical direction to prevent jumping teeth. The correct method is slowly screw in the direction of thread rotation.
4. Remove the handle (break off the mounting handle)Use a breaker to break the mounting handle. Use about 200g of coconut to hit the breaker instantly, and the handle can be removed. Do not use the mounting wrench to rotate in the opposite direction. Do not break the mounting handle. This situation is very easy. As a result, the tail shank was broken and the wire was pulled out.
5. UnscrewWhen installation problems occur during the installation of the wire thread insert (such as jumping teeth), the thread insert needs to be removed, and a special sleeve remover should be used to remove the wire thread insert.
-
Fruugo ID:
355054258-771888872
-
EAN:
9396322041137
Produktsikkerhedsinformation
Se venligst produktsikkerhedsoplysningerne, der er specifikke for dette produkt, beskrevet nedenfor
Følgende oplysninger leveres af den uafhængige tredjepartsforhandler, der sælger dette produkt.
Sikkerhedsadvarsler:
WARNING: Beware of hidden hazards in walls or other mounting surfaces
Levering og returnering
Sendt inden for 3 dage
Afsendes fra Kina.
Vi gør vores bedste for at sikre, at de produkter, du bestiller, leveres til dig fuldt ud og i henhold til dine specifikationer. Skulle du dog modtage en ufuldstændig ordre eller andre ting end dem, du bestilte, eller der er en anden grund til, at du ikke er tilfreds med ordren, kan du returnere ordren eller produkter inkluderet i ordren og modtage en fuld refusion for varerne. Se fuld returpolitik
Detaljer om produktoverholdelse
Se venligst overensstemmelsesoplysningerne, der er specifikke for dette produkt, beskrevet nedenfor.
Følgende oplysninger leveres af den uafhængige tredjepartsforhandler, der sælger dette produkt.
Producent:
De følgende oplysninger angiver kontaktoplysningerne for producenten af det relevante produkt, der sælges på Fruugo.
- Chen ShaoMao
- Lixian Maisite Trading Co., Ltd.
- Group 8
- Wugong Village
- Xiaodukou Town
- Lixian County
- CN
- 415500
- liuanjinglaj@outlook.com
- 13192770024
Ansvarlig person i EU:
De følgende oplysninger angiver kontaktoplysningerne for den ansvarlige person i EU. Den ansvarlige person er den udpegede økonomiske aktør med hovedsæde i EU, der er ansvarlig for overensstemmelsesobligationerne i forbindelse med det relevante produkt, der sælges til den Europæiske Union.
- e Vatmaster Consulting GmbH
- e Vatmaster Consulting GmbH
- RaiffeisenstraBe 2 B11
- Rodgau
- DE
- 63110
- contact@evatmaster.com
- 49 61062699873